SCCP Calling Party Address Configuration

You can configure the calling party address fields output in Signaling Connection Control Part (SCCP) messages sent through CAMEL Gateway.

SCCP Calling Party Address Configuration Parameters describes the create_config.py parameters necessary for configuring calling party address fields sent in SCCP messages and shows default values for each parameter.
Note: System administrators configure calling party address per processing blade. The values specified for the first processing blade are used as the default values for each additional processing blade.
Table 1. SCCP Calling Party Address Configuration Parameters
Parameter Description Default Value
SCCP Address Specifies the value to use in the calling party address field of the SCCP message. Valid values are:
  • incoming — Use the received SCCP called party address as the calling party address. If you specify incoming, no further questions relating to the SCCP address are asked.
  • pc — To specify a point code as the calling party address. You must answer an additional question to specify the point code.
  • gt — To specify a global title as the calling party address. You must answer additional questions to specify the global title.

create_config.info question: Engine 1:Cluster 1:LogicalBlade 1:What SCCP address should be used for this blade (incoming/pc/gt)?

incoming
Point Code If SCCP Address is set to pc, specifies the point code to use in the SCCP calling party address.

create_config.info question: Engine 1:Cluster 1:LogicalBlade 1:What is the SCCP point code of this blade?

None
GT Type If SCCP Address is set to gt, specifies the type of the global title to use in the SCCP calling address. Valid values are:
  • 1 — Use digits and nature of address
  • 2 — Use digits and translation type
  • 3 — Use digits, translation type, and numbering plan
  • 4 — Use digits, translation type, numbering plan, and nature of address

create_config.info question: Engine 1:Cluster 1:LogicalBlade 1:What is the SCCP global title type for this blade?

4
GT Digits If SCCP Address is set to gt, specifies the global title digits to use in the SCCP calling party address. You must specify a non-negative integer.

create_config.info question: Engine 1:Cluster 1:LogicalBlade 1:What are the SCCP global title digits for this blade?

12345678
GT Nature of Address
If SCCP Address is set to gt, specifies the nature of address of the global title to use in the SCCP calling address. Specify a value in the range 0 to 127:
  • 0 — Unknown
  • 1 — Subscriber
  • 3 — National
  • 4 — International
  • All other values are spare or reserved

create_config.info question: Engine 1:Cluster 1:LogicalBlade 1:What is the SCCP global title nature of address for this blade?

4
GT Translation Type If SCCP Address is set to gt, specifies the translation type of the global title to use in the SCCP calling address. Specify a value in the range 0 to 255.

create_config.info question: Engine 1:Cluster 1:LogicalBlade 1:What is the SCCP global title translation type for this blade?

None
GT Numbering Plan If SCCP Address is set to gt, specifies the numbering plan of the global title to use in the SCCP calling address. Specify a value in the range 0 to 15:
  • 0 — Unknown
  • 1 — ISDN/telephony numbering plan (ITU-T E.163 and E.164)
  • 2 — Generic numbering plan
  • 3 — Data numbering plan (ITU-T X.121)
  • 4 — Telex numbering plan (ITU-T F.69)
  • 5 — Maritime mobile numbering plan (ITU-T E.210, E.211)
  • 6 — Land mobile numbering plan (ITU-T E.212)
  • 7 — ISDN/mobile numbering plan (ITU-T E.214)
  • All other values are spare or reserved

create_config.info question: Engine 1:Cluster 1:LogicalBlade 1:What is the SCCP global title numbering plan for this blade?

1